XBeam2D XFrame2D Eurocode Steel: Difference between revisions

From Struct4u
Jump to navigation Jump to search
No edit summary
No edit summary
Line 1: Line 1:
[[File:XBeam2DEurocode.png|675x675px]]
[[File:XBeam2DEurocode.png|675x675px]]


'''EN 1993-1-1 / EN 1995-1-1'''
'''EN 1993-1-1 / EN 1995-1-1'''


Specifically and only for the check according to Eurocode 3: NEN-EN 1993-1-1 respectively Eurocode 5: NEN-EN 1995-1-1 data can be inserted.  
Specifically and only for the check according to Eurocode 3: NEN-EN 1993-1-1 respectively Eurocode 5: NEN-EN 1995-1-1 data can be inserted.  


'''Beam group'''
'''Beam group'''


Specifically and only for the lateral-torsional buckling resistance check a beam group can be inserted here. XFrame2d automatically detects for which beams this qualifies. Only the beams which are connected by a fully fixed connection to this particular beam and have the same profile will be showed. You can select which beams should be taken into account. For this group you subsequently enter the length between the lateral restraints and the buckling length out of plane.     
Specifically and only for the lateral-torsional buckling resistance check a beam group can be inserted here. XFrame2d automatically detects for which beams this qualifies. Only the beams which are connected by a fully fixed connection to this particular beam and have the same profile will be showed. You can select which beams should be taken into account. For this group you subsequently enter the length between the lateral restraints and the buckling length out of plane.     
'''Cantilever'''


'''Cantilever'''
'''Cantilever'''


Setting if the beam should be considered as a cantilever.
Setting if the beam should be considered as a cantilever.


'''Lateral torsional buckling'''
'''Lateral torsional buckling'''
Line 24: Line 19:


This is only relevant for the check of lateral torsional buckling. You can enter the lateral supports for the top and the bottom flange.     
This is only relevant for the check of lateral torsional buckling. You can enter the lateral supports for the top and the bottom flange.     
'''There are 3 possibilities:'''


'''There are 3 possibilities:'''
'''There are 3 possibilities:'''
Line 33: Line 29:
    
    
3. Node numbers Selecting the node numbers which are in the beam group.     
3. Node numbers Selecting the node numbers which are in the beam group.     
'''Buckling length'''


'''Buckling length'''
'''Buckling length'''
Line 39: Line 36:


However buckling out of the plane should be reviewed. Default the buckling lengths out of plane are taken equal to the beam length. In case this does not hold a different buckling length can be entered.     
However buckling out of the plane should be reviewed. Default the buckling lengths out of plane are taken equal to the beam length. In case this does not hold a different buckling length can be entered.     
'''Check deflection'''


'''Check deflection'''
'''Check deflection'''


Setting if deflection has to be checked.
Setting if deflection has to be checked.


'''Type'''  
'''Type'''  


This influences the requirement of additional deflection.
This influences the requirement of additional deflection.  


'''Additional deflection'''
'''Additional deflection'''


Requirement of additional deflection.
Requirement of additional deflection.  


'''Final deflection'''
'''Final deflection'''


Requirements of final deflection.
Requirements of final deflection.  


'''Pre-camber'''
'''Pre-camber'''


The size of pre-camber in mm.
The size of pre-camber in mm.

Revision as of 04:02, 6 September 2022

XBeam2DEurocode.png

EN 1993-1-1 / EN 1995-1-1

Specifically and only for the check according to Eurocode 3: NEN-EN 1993-1-1 respectively Eurocode 5: NEN-EN 1995-1-1 data can be inserted.

Beam group

Specifically and only for the lateral-torsional buckling resistance check a beam group can be inserted here. XFrame2d automatically detects for which beams this qualifies. Only the beams which are connected by a fully fixed connection to this particular beam and have the same profile will be showed. You can select which beams should be taken into account. For this group you subsequently enter the length between the lateral restraints and the buckling length out of plane. Cantilever

Cantilever

Setting if the beam should be considered as a cantilever.

Lateral torsional buckling

Amount of lateral supports / distances between lateral supports

This is only relevant for the check of lateral torsional buckling. You can enter the lateral supports for the top and the bottom flange. There are 3 possibilities:

There are 3 possibilities:

1. Number: The amount of lateral supports. That are the extra (lateral supports) between the supports distributed over the length of the beam(group)

2. Distances: The lengths between the lateral restraints from the beginning of the beam (group). The syntax is length1 length2 amountxlenght3.. etc. For example 3000 3x2200 2800

3. Node numbers Selecting the node numbers which are in the beam group. Buckling length

Buckling length

The buckling length out of plane. According to the check by Eurocode 3: NEN-EN 1993-1-1 resp. Eurocode 5: NEN-EN 1995-1-1 this is based on a geometric non linear force distribution. This means that the buckling of the beams in the plane of the frameworks is provided implicit. For every load combination the internal stability is determined iteratively.

However buckling out of the plane should be reviewed. Default the buckling lengths out of plane are taken equal to the beam length. In case this does not hold a different buckling length can be entered. Check deflection

Check deflection

Setting if deflection has to be checked.

Type

This influences the requirement of additional deflection.

Additional deflection

Requirement of additional deflection.

Final deflection

Requirements of final deflection.

Pre-camber

The size of pre-camber in mm.