Struct4U at 09:52, 11 December 2023

2023-12-11T09:52:08Z

← Older revision		Revision as of 09:52, 11 December 2023
Line 79:		Line 79:

	All the load cases and load combinations for snow and wind are created automatically. You can also change and extend these loads.		All the load cases and load combinations for snow and wind are created automatically. You can also change and extend these loads.

			To work with surface loads, there are a few '''important ground rules''', though. What you need to know.

			* To work with the load generator, shells must be entered. From the shells the surface loads are generated. Shells must be drawn clockwise from the outside so that the z-axis of the shell faces outward.

			* The shell (and therefore the surface load) must always be "'''edged'''" by surface load bearing beams. Even if the load (by load bearing direction) does not go there.

			* Work accurately. All beams / nodes must lie neatly in the plane of the shell resp. surface load. A skewed plane is not supported. So this requires you to work accurately.

			* Also, always check that the beam loads are properly generated from the surface loads. You do this by turning on "'''Derived beam loads'''". Check if the direction of the load transfer is entered correctly. If it is not correct, change the direction of the load transfer at the shells and restart the load generator.

Struct4U: Created page with " BACK With the load generator you generate all snow and wind loads, including all load combinations, in no time. In particular, wind loads according to Eurocode are extensive and therefore laborious. The load generator takes that work out of your hands. Before you start the load generator, you will first have to enter all the Outer Panels 515x515px '''Design working life''' The desi..."

2022-09-10T12:49:31Z

Created page with " BACK With the load generator you generate all snow and wind loads, including all load combinations, in no time. In particular, wind loads according to Eurocode are extensive and therefore laborious. The load generator takes that work out of your hands. Before you start the load generator, you will first have to enter all the Outer Panels 515x515px '''Design working life''' The desi..."

New page

[[Documentation XFEM4U | BACK]]

With the load generator you generate all snow and wind loads, including all load combinations, in no time. In particular, wind loads according to Eurocode are extensive and therefore laborious. The load generator takes that work out of your hands.

Before you start the load generator, you will first have to enter all the [[XFEM4U Outer Panels|Outer Panels]]

[[File:XFEM4ULoadGenerator.png|515x515px]]

'''Design working life'''

The design working life of the building in years

'''Imperfections'''

It can be set whether you want to take imperfections into account or not.

'''Wind loads according to EN-1991-1-4'''

'''Wind zone'''

Dependent on the location of the structure, the wind zone is chosen. This value differs per country.

'''Terrain category'''

Based on local circumstances the terrain category is chosen.

'''Height above terrain'''

The height of the building above terrain in meters.

'''Velocity pressure'''

Calculated velocity pressure

'''Structural factor'''

Structural factor according to 6.3

'''Correlation'''

Setting or wind pressures on facades must be reduced by 0.85. E.g. according to Dutch NAD art. 7.2.2(3).

'''Wind in +X'''

Select whether the wind has to be generated in positive x-direction.

'''Wind in -X'''

Select whether the wind has to be generated in negative x-direction.

'''Wind in +Y'''

Select whether the wind has to be generated in positive y-direction.

'''Wind in -Y'''

Select whether the wind has to be generated in negative y-direction.

The internal under- and over pressure is dependent on the size of the openings in the walls.

'''Snow loads according to EN-1991-1-3'''

Select whether the snow load needs to be generated or not.

All the load cases and load combinations for snow and wind are created automatically. You can also change and extend these loads.

XFEM4U Load generator - Revision history

Struct4U at 09:52, 11 December 2023