XBeam2D XFrame2D Menu - Revision history

Struct4U at 06:09, 7 September 2022

2022-09-07T06:09:41Z

← Older revision		Revision as of 06:09, 7 September 2022
Line 1:		Line 1:




	~~[[File:XBeam2DFixed.png]]~~
	{\| class="wikitable"		{\| class="wikitable"
	\|+		\|+
Line 67:		Line 63:
	\|-		\|-
	\|'''Geometry'''		\|'''Geometry'''
	\|		\|[[File:Struct4UBeam.png\|35x35px]]
	\|'''Beam'''		\|'''Beam'''
	\|Inserting [[XBeam2D Beams\|Beams]]		\|Inserting [[XBeam2D Beams\|Beams]]
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UNode.png\|33x33px]]
	\|'''Node'''		\|'''Node'''
	\|Inserting ~~nodes~~		\|Inserting [[XBeam2D Nodes\|Nodes]]
	\|-		\|-
	\|		\|
	\|[[File:XBeam2DPinned.png\|33x33px]]		\|[[File:XBeam2DPinned.png\|33x33px]]
	\|'''Pinned'''		\|'''Pinned'''
	\|Pinned support		\|Pinned support. See [[XBeam2D Supports\|Supports]]
	\|-		\|-
	\|		\|
Line 125:		Line 121:
	\|'''q-load'''		\|'''q-load'''
	\|Evenly distributed beam load or a linear varying beam load ( for example triangle load)		\|Evenly distributed beam load or a linear varying beam load ( for example triangle load)
			See also [[XBeam2D Loads\|Loads]]
	\|-		\|-
	\|		\|
Line 152:		Line 149:
	\|-		\|-
	\|'''Edit'''		\|'''Edit'''
	\|		\|[[File:Struct4UUndo.png\|34x34px]]
	\|'''Undo'''		\|'''Undo'''
	\|Undo an adaptation. Every adaptation is saved intern. With this function you can undo one or multiple adaptations. There is no limit in the amount of steps that you can go back.		\|Undo an adaptation. Every adaptation is saved intern. With this function you can undo one or multiple adaptations. There is no limit in the amount of steps that you can go back.
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4URedo.png\|34x34px]]
	\|'''Redo'''		\|'''Redo'''
	\|Redo an adaptation.		\|Redo an adaptation.
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4USelect.png\|32x32px]]
	\|'''Select'''		\|'''Select'''
	\|Set setting to : Select. In this modus you can select a profile ( make active) in the graphical screen.		\|Set setting to : Select. In this modus you can select a profile ( make active) in the graphical screen.
Line 172:		Line 169:
	\|-		\|-
	\|'''View'''		\|'''View'''
	\|		\|[[File:Struct4UZoomWindow.png\|34x34px]]
	\|'''Zoom window'''		\|'''Zoom window'''
	\|Set setting to : '''Zoom window'''. This function is used to zoom into a certain part in the cross section design.		\|Set setting to : '''Zoom window'''. This function is used to zoom into a certain part in the cross section design.
Line 179:		Line 176:
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UPan.png\|46x46px]]
	\|'''Pan'''		\|'''Pan'''
	\|By the use of pan you can drag / move a zoomed part of your drawing. Other parts of the construction will be presented.		\|By the use of pan you can drag / move a zoomed part of your drawing. Other parts of the construction will be presented.
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UZoomExtents.png\|35x35px]]
	\|'''Zoom extents'''		\|'''Zoom extents'''
	\|Set the setting to Zoom extents. This function is used to show everything in full screen. The modus is automatically turned off after zooming out.		\|Set the setting to Zoom extents. This function is used to show everything in full screen. The modus is automatically turned off after zooming out.
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UPreviousView.png\|34x34px]]
	\|'''Previous view'''		\|'''Previous view'''
	\|With zoom view you can eventually zoom into a part of the construction in multiple steps. With the function previous view you go back 1 step.		\|With zoom view you can eventually zoom into a part of the construction in multiple steps. With the function previous view you go back 1 step.
Line 199:		Line 196:
	\|-		\|-
	\|'''Options'''		\|'''Options'''
	\|		\|[[File:Struct4UDistance.png\|37x37px]]
	\|'''Distance'''		\|'''Distance'''
	\|Set the setting to: '''Distance'''. In this modus distances can be measured. There is automatically snapped to all the occurring contour points, and points in the middle of all the lines. This modus is not turned off.		\|Set the setting to: '''Distance'''. In this modus distances can be measured. There is automatically snapped to all the occurring contour points, and points in the middle of all the lines. This modus is not turned off.
Line 217:		Line 214:
	\|-		\|-
	\|'''Help'''		\|'''Help'''
	\|		\|[[File:Struct4UHelp.png\|26x26px]]
	\|'''Help'''		\|'''Help'''
	\|Open help file.		\|Open help file.

Struct4U at 05:57, 7 September 2022

2022-09-07T05:57:56Z

← Older revision		Revision as of 05:57, 7 September 2022
Line 1:		Line 1:




			[[File:XBeam2DFixed.png]]
	{\| class="wikitable"		{\| class="wikitable"
	\|+		\|+
Line 7:		Line 12:
	\|-		\|-
	\|'''File'''		\|'''File'''
	\|		\|[[File:Struct4UNew.png\|32x32px]]
	\|'''New'''		\|'''New'''
	\|New input		\|New input
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UOpen.png\|30x30px]]
	\|'''Open'''		\|'''Open'''
	\|Open an already existing file		\|Open an already existing file
Line 22:		Line 27:
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4USave.png\|32x32px]]
	\|'''Save'''		\|'''Save'''
	\|Save the input in a file		\|Save the input in a file
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4USave.png\|32x32px]]
	\|'''Save as'''		\|'''Save as'''
	\|Save the input in another (copy ) file		\|Save the input in another (copy ) file
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UPreview.png\|34x34px]]
	\|'''Preview'''		\|'''Preview'''
	\|Making a print preview on the screen		\|Making a print preview on the screen
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UPrint.png\|33x33px]]
	\|'''Print'''		\|'''Print'''
	\|Print of the calculation		\|Print of the calculation
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4URTF.png\|33x33px]]
	\|'''RTF-output'''		\|'''RTF-output'''
	\|Save the output as an RTF-format (MS-Word)		\|Save the output as an RTF-format (MS-Word)
	\|-		\|-
	\|		\|
	\|		\|[[File:Struct4UPDF.png\|33x33px]]
	\|'''PDF-output'''		\|'''PDF-output'''
	\|Save the output as a PDF-format		\|Save the output as a PDF-format
Line 72:		Line 77:
	\|-		\|-
	\|		\|
	\|		\|[[File:XBeam2DPinned.png\|33x33px]]
	\|'''Pinned'''		\|'''Pinned'''
	\|Pinned support		\|Pinned support
	\|-		\|-
	\|		\|
	\|		\|[[File:XBeam2DRoller.png\|33x33px]]
	\|'''X-roller'''		\|'''X-roller'''
	\|Roller support in the x-direction		\|Roller support in the x-direction
	\|-		\|-
	\|		\|
	\|		\|[[File:XBeam2DRoller2.png\|40x40px]]
	\|'''Z-roller'''		\|'''Z-roller'''
	\|Roller support in the z-direction		\|Roller support in the z-direction
	\|-		\|-
	\|		\|
	\|		\|[[File:XBeam2DFixed.png\|37x37px]]
	\|'''Fixed'''		\|'''Fixed'''
	\|Fixed support		\|Fixed support
	\|-		\|-
	\|		\|
	\|		\|[[File:XBeam2DSpringZ.png\|39x39px]]
	\|'''Z-spring'''		\|'''Z-spring'''
	\|Spring support in z-direction. Translation spring in z-direction.		\|Spring support in z-direction. Translation spring in z-direction.
	\|-		\|-
	\|		\|
	\|		\|[[File:XBeam2DSpringX.png\|47x47px]]
	\|'''X-spring'''		\|'''X-spring'''
	\|Spring support in x-direction. Translation spring in x-direction.		\|Spring support in x-direction. Translation spring in x-direction.
	\|-		\|-
	\|		\|
	\|		\|[[File:XBeam2DSpringY.png\|43x43px]]
	\|'''R-spring'''		\|'''R-spring'''
	\|Spring support around y-axis. Rotation spring at y-axis.		\|Spring support around y-axis. Rotation spring at y-axis.
Line 117:		Line 122:
	\|-		\|-
	\|'''Load'''		\|'''Load'''
	\|		\|[[File:Load-q.png]]
	\|'''q-load'''		\|'''q-load'''
	\|Evenly distributed beam load or a linear varying beam load ( for example triangle load)		\|Evenly distributed beam load or a linear varying beam load ( for example triangle load)
	\|-		\|-
	\|		\|
	\|		\|[[File:Load-F.png\|31x31px]]
	\|'''F-load'''		\|'''F-load'''
	\|Point load on beam		\|Point load on beam
	\|-		\|-
	\|		\|
	\|		\|[[File:Load-M.png\|35x35px]]
	\|'''M-load'''		\|'''M-load'''
	\|Moment on beam		\|Moment on beam
	\|-		\|-
	\|		\|
	\|		\|[[File:Cur nodeload.png\|36x36px]]
	\|'''Node load'''		\|'''Node load'''
	\|Load on node (Fx force in x-direction, Fz force in z-direction and/or My moment around y-axis)		\|Load on node (Fx force in x-direction, Fz force in z-direction and/or My moment around y-axis)

Struct4U: Created page with "{| class="wikitable" |+ !Tab on ribbon !Icon !Command !Description |- |'''File''' | |'''New''' |New input |- | | |'''Open''' |Open an already existing file |- | | |'''Close''' |Close the opened file |- | | |'''Save''' |Save the input in a file |- | | |'''Save as''' |Save the input in another (copy ) file |- | | |'''Preview''' |Making a print preview on the screen |- | | |'''Print''' |Print of the calculation |- | | |'''RTF-output''' |Save the output as an RTF-format (MS..."

2022-09-07T05:40:32Z

Created page with "{| class="wikitable" |+ !Tab on ribbon !Icon !Command !Description |- |'''File''' | |'''New''' |New input |- | | |'''Open''' |Open an already existing file |- | | |'''Close''' |Close the opened file |- | | |'''Save''' |Save the input in a file |- | | |'''Save as''' |Save the input in another (copy ) file |- | | |'''Preview''' |Making a print preview on the screen |- | | |'''Print''' |Print of the calculation |- | | |'''RTF-output''' |Save the output as an RTF-format (MS..."

New page

{| class="wikitable"
|+
!Tab on ribbon
!Icon
!Command
!Description
|-
|'''File'''
|
|'''New'''
|New input
|-
|
|
|'''Open'''
|Open an already existing file
|-
|
|
|'''Close'''
|Close the opened file
|-
|
|
|'''Save'''
|Save the input in a file
|-
|
|
|'''Save as'''
|Save the input in another (copy ) file
|-
|
|
|'''Preview'''
|Making a print preview on the screen
|-
|
|
|'''Print'''
|Print of the calculation
|-
|
|
|'''RTF-output'''
|Save the output as an RTF-format (MS-Word)
|-
|
|
|'''PDF-output'''
|Save the output as a PDF-format
|-
|
|
|'''Exit'''
|Close the program
|-
|
|
|
|
|-
|'''Geometry'''
|
|'''Beam'''
|Inserting [[XBeam2D Beams|Beams]]
|-
|
|
|'''Node'''
|Inserting nodes
|-
|
|
|'''Pinned'''
|Pinned support
|-
|
|
|'''X-roller'''
|Roller support in the x-direction
|-
|
|
|'''Z-roller'''
|Roller support in the z-direction
|-
|
|
|'''Fixed'''
|Fixed support
|-
|
|
|'''Z-spring'''
|Spring support in z-direction. Translation spring in z-direction.
|-
|
|
|'''X-spring'''
|Spring support in x-direction. Translation spring in x-direction.
|-
|
|
|'''R-spring'''
|Spring support around y-axis. Rotation spring at y-axis.
|-
|
|
|'''Internal hinge'''
|Internal hinge in beam. By this you can quickly insert a gerber beam.
|-
|
|
|
|
|-
|'''Load'''
|
|'''q-load'''
|Evenly distributed beam load or a linear varying beam load ( for example triangle load)
|-
|
|
|'''F-load'''
|Point load on beam
|-
|
|
|'''M-load'''
|Moment on beam
|-
|
|
|'''Node load'''
|Load on node (Fx force in x-direction, Fz force in z-direction and/or My moment around y-axis)
|-
|
|
|'''Node displacement'''
|Forced node displacement of the node. ( dx displacement in x-direction, dz displacement in z-direction and/or dr rotation around the y-axis).
|-
|
|
|
|
|-
|'''Edit'''
|
|'''Undo'''
|Undo an adaptation. Every adaptation is saved intern. With this function you can undo one or multiple adaptations. There is no limit in the amount of steps that you can go back.
|-
|
|
|'''Redo'''
|Redo an adaptation.
|-
|
|
|'''Select'''
|Set setting to : Select. In this modus you can select a profile ( make active) in the graphical screen.
|-
|
|
|
|
|-
|'''View'''
|
|'''Zoom window'''
|Set setting to : '''Zoom window'''. This function is used to zoom into a certain part in the cross section design.

Method: With the left mouse button pushed, you make a rectangular window from the left bottom to the right top. The modus is automatically turned off after the zooming.
|-
|
|
|'''Pan'''
|By the use of pan you can drag / move a zoomed part of your drawing. Other parts of the construction will be presented.
|-
|
|
|'''Zoom extents'''
|Set the setting to Zoom extents. This function is used to show everything in full screen. The modus is automatically turned off after zooming out.
|-
|
|
|'''Previous view'''
|With zoom view you can eventually zoom into a part of the construction in multiple steps. With the function previous view you go back 1 step.
|-
|
|
|
|
|-
|'''Options'''
|
|'''Distance'''
|Set the setting to: '''Distance'''. In this modus distances can be measured. There is automatically snapped to all the occurring contour points, and points in the middle of all the lines. This modus is not turned off.

Method: Select the starting point while using the snap-function. With the left mouse button pushed you go to another known point in the construction. While pushing the left mouse button, a measure line is drawn and a little window is displayed wherein the distances dL, dy and dz in mm are shown.
|-
|
|
|'''Settings'''
|Adjusting the settings.
|-
|
|
|
|
|-
|'''Help'''
|
|'''Help'''
|Open help file.
|-
|
|
|'''Information'''
|Information with regard to the application and license agreement.
|}